I saw a whimsical stuffed owl in a Pottery Barn Kids catalog, and I thought it would be fun to try. This is my version. It's a bit skinner and I think the long legs are really funny. It must be some kind of burrowing owl, or...something.
These are the fabrics I used, but you can use whatever scraps you have around. For the eyes, you need a non-fraying material such as felt or fleece.
- Upper leg / foot/ wing fabric (yellow cotton)
- Leg fabric (blue fleece)
- Body fabric (checkered blue cotton)
- Face fabric (tan velour)
- Eye fabric (felt and fleece)
- Fusible Interfacing
- Matching thread
Print the pattern using these links-Page 1 (foot, beak, center eye, back body part A)
Page 2 (wing, upper leg, top front body)
Page 3 (back body part B, bottom front body)
Cut out all of your pieces. The pattern already includes a 1/2 inch seam allowance. When you cut the feet, wings, and upper legs, make sure two pieces are traced on the right side of the fabric and two pieces are traced on the wrong side of fabric so they will match up when you sew them together. In addition to the pattern pieces, also cut out 4 rectangles 2.5 by 6 inches in your leg material. Also cut out 4 rectangles of the same size from the interfacing. Using the center eye piece as a template, cut two circles slightly larger from a complimentary color of felt, and then cut out two more circles even larger from another color of felt (see the pic of the eyes below).
Fuse the interfacing to the wrong side of your 4 leg pieces.
Pin your feet and upper legs, right sides together, to the ends of your legs.
Sew them on with a 1/2 inch seam allowance. Make sure you sew very securely if your kids are like mine and like to swing stuffed animals around by their legs.
When you're done sewing, open them up. They should look like this.
You'll notice that the upper legs have one side that is wider than the other. Make sure to match them up correctly with the other leg piece so that the sides are the same shape. Place two corresponding leg pieces right sides together and pin.
Then sew all the way around the legs and feet with a 1/2 inch seam allowance, leaving only the top of the upper legs open. I used blue thread on the leg part and yellow on the yellow fabric so it won't show through when it's turned out.
Trim the seams and clip the corners. Cut wedges out of the rounded edges and flip it right-side-out. Stuff with Polyfil. Use a chopstick or crochet hook to get it all the way down into the foot. If you want, you can add some plastic pellets or beans to the feet before stuffing to give them some weight.
Now the legs are done. Set them aside.
With right sides together, sew the wings, leaving the tops open. Trim seams and clip corners.
Flip them right-side-out and topstitch, again leaving the tops open.
Pin the wings to the top edge of the bottom front piece, 3/4 of an inch from the sides.
Add the top front piece, right sides together and stitch with a 1/2 in seam.
Open it up and it's time to add the eyes.
Take the largest of your 3 circles per eye that you have cut out and place it where you want on the face. Sew all the way around the edge with matching thread. Keep in mind that you're going to lose a half inch around the outside edge of the body when you sew the back on.
Ok yeah....that's...creepy. Better finish those quick...
Do the same thing with the two smaller circles and the beak.
Pin the legs to the bottom of the body. Make sure the Polyfil is down low enough into the legs so you don't sew over it. The wider sides of the upper leg should be facing the outside of the bird.
Sandwich the legs with the back body piece and pin. Then, again with a 1/2 in seam, sew all the way around the body, being careful to keep the legs inside. Leave about 3 inches open on one of the sides for turning.
Clip corners and cut wedges on the curves. Turn it right side out.
Stuff it and hand sew the turning opening with an invisible stitch. If you'd like you can put some beans or plastic pellets in the bum to give it some weight.
You're done! Now make him a friend.